Help! Small engine repair!
Page 1 of 4 123 ... LastLast
Results 1 to 10 of 34
Like Tree7Likes

Thread: Help! Small engine repair!

  1. #1
    Typical 1563621's Avatar
    Join Date
    Oct 2010
    Location
    Waretown
    Posts
    992
    Member #
    7985
    Thanked
    162 times

    Help! Small engine repair!

    In toms river, have snowblower. Clogged carb, fixed, but need help getting back together, bad back. Got it started but gas leak.
    NRA LIFE, GCA MEMBER, IATSE LOCAL#21,CJR&P.

  2. #2
    Typical 1563621's Avatar
    Join Date
    Oct 2010
    Location
    Waretown
    Posts
    992
    Member #
    7985
    Thanked
    162 times
    Can wait a week or so. cash or ammo trade.
    NRA LIFE, GCA MEMBER, IATSE LOCAL#21,CJR&P.

  3. #3
    Dominant Buck GhostBear's Avatar
    Join Date
    Nov 2005
    Posts
    10,211
    Member #
    561
    Thanked
    1568 times
    Where is the leak? Float bowl? Or fuel line?
    Hunt with a Vizsla, Cause life's to short to hunt with an ugly dog!

  4. Remove Advertisements
    NewJerseyHunter.com
    Advertisements
     

  5. #4
    Dominant Buck Liv2hunt's Avatar
    Join Date
    Sep 2005
    Posts
    6,602
    Member #
    398
    Thanked
    532 times
    is it the float? try and start it some times they will un stick the float
    I just want to Hunt...

  6. #5
    Typical MxRider18's Avatar
    Join Date
    Oct 2013
    Location
    Bucks County, PA
    Posts
    942
    Member #
    29912
    Thanked
    488 times
    Did you install your needle valve correctly? Does the float pin have varnish on it?
    From My Cold Dead Hands


    Local 254

  7. #6
    Typical 1563621's Avatar
    Join Date
    Oct 2010
    Location
    Waretown
    Posts
    992
    Member #
    7985
    Thanked
    162 times
    Bowl leak. Back and bending over doesn't work well. Got it back together and it started and ran but leak at bowl. washer prob. not in right. Last spring ran dry & picked up some shit in carb.
    NRA LIFE, GCA MEMBER, IATSE LOCAL#21,CJR&P.

  8. #7
    Typical 1563621's Avatar
    Join Date
    Oct 2010
    Location
    Waretown
    Posts
    992
    Member #
    7985
    Thanked
    162 times
    No varnish.
    NRA LIFE, GCA MEMBER, IATSE LOCAL#21,CJR&P.

  9. #8
    Typical MxRider18's Avatar
    Join Date
    Oct 2013
    Location
    Bucks County, PA
    Posts
    942
    Member #
    29912
    Thanked
    488 times
    Is their a rubber gasket around the float bowl where it mounts to the carb? Or is it leaking out the bottom of the carb?
    From My Cold Dead Hands


    Local 254

  10. #9
    Typical 1563621's Avatar
    Join Date
    Oct 2010
    Location
    Waretown
    Posts
    992
    Member #
    7985
    Thanked
    162 times
    Very small rubber gasket.
    NRA LIFE, GCA MEMBER, IATSE LOCAL#21,CJR&P.

  11. #10
    Typical megavites's Avatar
    Join Date
    Oct 2014
    Location
    Jackson
    Posts
    620
    Member #
    34340
    Thanked
    301 times
    make sure you have the clip installed correctly on the needlevalve and that it moves freely with the float. Also check your rubber gasket is seated correctly.
    howell boy likes this.
    "A goal is not always meant to be reached, it often serves simply as something to aim at." Bruce Lee

Page 1 of 4 123 ... LastLast

Sponsors

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. small engine repair needed
    By brokeleghunter in forum General Comments & Information
    Replies: 6
    Last Post: 12-03-2013, 02:23 PM
  2. small engine repair
    By conman in forum General Comments & Information
    Replies: 1
    Last Post: 05-11-2013, 04:38 AM
  3. Small Engine question
    By polarbear in forum How To
    Replies: 12
    Last Post: 06-01-2010, 10:26 PM
  4. small engine repair
    By Fireman60 in forum General Comments & Information
    Replies: 8
    Last Post: 05-27-2009, 09:47 PM